6th international CAN Conference 1999
 

Contents
 

Session 1: Transceiver
Chairman: V. Schiffer (Rockwell Automation)

• Controller and U435 Line Interface
  L. Perier (ST-Microelectronics)
• Single Wire CAN Physical Layer
  R. Baird, Chr. Lupini (Delphi Automotive Systems)
• A Transparent Approach to Fault-tolerant Broadcast in CAN
  M. A/ Livani (University of Ulm)

Session 2: CAN Physical Layer
Chairman: R. Hugel (Robert Bosch)

• CAN Physical Layer for Special Applications
  Prof. Dr. H. Beikirch (University of Rostock)
• Wireless CAN Extensions
  Dr. L. Rauchhaupt (lfak e.V.)
• Designing an Industrial Network with Unshielded Cable and IDC Connectors
  B. Lounsbury (Rockwell Automation)

Session 3: Application Modeling
Chairman: A. Krappel (Hitachi Europe)

• Using UML for Modeling CAN Systems
  D. Berglund (Kvaser AB)
• CANopen Device Descriptions Using General Purpose Modeling Languages
  Dr. M. Wollschlager (University of Magdeburg)
• A CAN-Bus-Based Safety-Critical Distributed Aero-Engine Control Systems Architecture Demonstrator
  Dr. H. A. Thompson (Rolls-Royce University)

Session 4: System Modeling
Chairman: H. Zeltwanger (CAN in Automation)

• Applying Modern Software Design Principles: A CAN Tool based on Extensibility
  M. Weseloh, Prof. R. Rudiger (FH BS/WF)
• Micro-Controller Simulator with CAN Functionality
  W. Wiewesiek, V. Nieten (NEC Electronics Germany)
• Efficient Protocol for Hard Real Time Communication on CAN
  S. Ouni, F. Kamoun (ENSI)

Session 5: Timing
Chairman: L.-B. Fredriksson (Kvaser)

• Scheduling and Synchronisation in CAN based Distributed Systems
  J. A. Fonseca, P. A. Fonseca (University of Aveiro)
• Enhancing the Efficiency of Controller Area Networks
  G. Cena, A. Valenzano (Cens-CNR Politecnico Torino)
• The Configuration of the CAN Bit Timing
  F. Hartwich, A. Bassemir (Robert Bosch GmbH)

Session 6: Gateway Technology
Chairman: L.-B. Fredriksson (Kvaser)

• Teleservice of CAN Systems via Internet
  G. Nusser, Prof. Dr. G. Gruhler (STA Reutlingen)
• CAN and the new IEEE 1451 Standard Transducer Interface
  D. Heffernan, P. Conway (PEI Technologies)
• Device Net over TCP/IP Gateway
  K. Ang (University of Warwick), B. Levine (Contemporary Control System)

Session 7: Industrial Application
Chairman: J. Dunn (Motorola)

• Injection Moulding Machines: A Distributed Control Approach
  P. Ursino (Automata S.p.A.), C. Melzer (Automata GmbH)
• CAN in Packaging and Plaster Machines
  F Riti (Eurosicrna), F. Pozzi (Oasys srl)
• CAN Bus to 6000m down in Oil Prospecting
  M. Parent, M. Cassin (Schlumberger S.R.P.C.)

Session 8: Transport Application
Chairman: A. Borin (Magneti Marelli)

• CAN Applications in Vehicles
  U. Dreher, H.-J. Aupperle (Smart Electronic Development GmbH)
• Implementing the CAN Calibration Protocol (CCP) in an SAE J1939 Application
  W. Vicek (Ascent Technologies Inc.), S. Ernest (Jacobs Vehicle Systems)
• Implementation of a CANopen Interface for the Remote Control of an Elevator System
  S. Vitturi (PST Galileo)

Session 9: Implementation
Chairman: K. Turski (NEC Electronics)

• Automotive Microcontrollers with On-Chip CAN
  A. Krappel, N. Hirayama (Hitachi Europe GmbH)
• Flex-CAN Communication Module for Embedded Microcontrollers
  G. Patel (Motorola Israel)
• New Generation of CAN Controller Supporting Higher Layer Protocols
  P. Hank (Philips Semiconductors)

Session 10: Bridge Technology
Chairman: V. Schiffer (Rockwell Automation)

• DSS - Distributed Diagnostic Systems
  A. Tamagnone (SixTau S.p.A.)
• Design and Implementation of a CAN/CAN Cut-through Bridge
  M. Tenruh (University of Sussex)
• High Level Performance Analysis of a Quadruple CAN Gateway
  F. Bogenberger (Motorola GmbH), U. Warschat (Audi AG)

Session 11: Physical Layer Testing
Chairman: R. Hugel (Robert Bosch)

• DeviceNet Physical Layer Design and Conformance Testing
  K. H. Tang, R. McLaughlin (Warwick Manufacturing Group)
• Monitoring CAN Performance in Installations with High Level of Interference
  J. Pinker, J. Skala ( University of West Bohemia)
• CAN Fault Injection
  Dr. M. Rimen, Dr. Christmansson (CR & TAB)

Session 12: Design Tools
Chairman: W. Reiss (Infineon Technologies)

• Conformity Certification Tools and Methods in a Multiplexed Architecture
  N. Lavorel (NSI)
• The Development of the Embedded Network Software based upon the Layer Model by Means of Static Configuration Tool
  A. Semjonov ( Motorola Research Lab.)
• A CAN Application Layer Protocol for the Implementation of Distributed Expert Systems
  A. Bonastre, R. Ors (University of Valencia)